Trinity Devboard PCB V1.0 Firmware. FreeRTOS is setup and the MCU reads IMU data over SPI fand Magnetometer data over I2C, each with a seperate task. Sensordata is then run though MadgwickAHRS and send over USB as serial packet data to use in trinity visualizer. Bare minimum functionality works and is replicated from the first prototype.

2026-09-13 19:51:03 +02:00
commit 7ee381de58
1630 changed files with 632404 additions and 0 deletions
@@ -0,0 +1,95 @@
+/* ----------------------------------------------------------------------
+ * Project:      CMSIS DSP Library
+ * Title:        arm_pid_init_q15.c
+ * Description:  Q15 PID Control initialization function
+ *
+ * $Date:        18. March 2019
+ * $Revision:    V1.6.0
+ *
+ * Target Processor: Cortex-M cores
+ * -------------------------------------------------------------------- */
+/*
+ * Copyright (C) 2010-2019 ARM Limited or its affiliates. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#include "arm_math.h"
+
+/**
+  @addtogroup PID
+  @{
+ */
+
+/**
+  @brief         Initialization function for the Q15 PID Control.
+  @param[in,out] S               points to an instance of the Q15 PID structure
+  @param[in]     resetStateFlag
+                   - value = 0: no change in state
+                   - value = 1: reset state
+  @return        none
+
+  @par           Details
+                   The <code>resetStateFlag</code> specifies whether to set state to zero or not. \n
+                   The function computes the structure fields: <code>A0</code>, <code>A1</code> <code>A2</code>
+                   using the proportional gain( \c Kp), integral gain( \c Ki) and derivative gain( \c Kd)
+                   also sets the state variables to all zeros.
+ */
+
+void arm_pid_init_q15(
+  arm_pid_instance_q15 * S,
+  int32_t resetStateFlag)
+{
+
+#if defined (ARM_MATH_DSP)
+
+  /* Derived coefficient A0 */
+  S->A0 = __QADD16(__QADD16(S->Kp, S->Ki), S->Kd);
+
+  /* Derived coefficients and pack into A1 */
+
+#ifndef  ARM_MATH_BIG_ENDIAN
+  S->A1 = __PKHBT(-__QADD16(__QADD16(S->Kd, S->Kd), S->Kp), S->Kd, 16);
+#else
+  S->A1 = __PKHBT(S->Kd, -__QADD16(__QADD16(S->Kd, S->Kd), S->Kp), 16);
+#endif
+
+#else
+
+  q31_t temp;                                    /* to store the sum */
+
+  /* Derived coefficient A0 */
+  temp = S->Kp + S->Ki + S->Kd;
+  S->A0 = (q15_t) __SSAT(temp, 16);
+
+  /* Derived coefficients and pack into A1 */
+  temp = -(S->Kd + S->Kd + S->Kp);
+  S->A1 = (q15_t) __SSAT(temp, 16);
+  S->A2 = S->Kd;
+
+#endif /* #if defined (ARM_MATH_DSP) */
+
+  /* Check whether state needs reset or not */
+  if (resetStateFlag)
+  {
+    /* Reset state to zero, The size will be always 3 samples */
+    memset(S->state, 0, 3U * sizeof(q15_t));
+  }
+
+}
+
+/**
+  @} end of PID group
+ */